A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
This post which follows about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is especially informative. You should keep reading.
Setting up a tub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a new one is additionally a reasonably hard job. If the old bathtub is easily obtainable, the job can relocate easily; if you need to open a wall to eliminate the old bathtub and also position the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. See to it you have qualified yourself for the task and also fit trying it. Rather than working with a specialist to take control of a halfway-completed project, it is much better to consider utilizing one prior to you begin. Possibilities are you may require a professional plumber to make tube links.
This write-up will certainly aid you mount a brand-new bathtub in your restroom if you have currently acquired a brand-new bathtub and also don't require to alter the arrangement of your previous supply of water pipelines.
Your devices and material list must comprise the following:
Planning for the Installation
Firstly, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to stop stress on the bath tub.
Fit the flexible faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, after that the first thing you must do is separate the supply of water. After doing so, turn on the taps to drain pipes any water remaining in the system. The procedure of removing the existing taps can be rather bothersome as a result of the limited accessibility that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleaned of any type of old securing substance.
Before moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Using both wooden boards under its feet, put the bathtub in the needed setting. The wooden boards are useful in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small points.
The following goal is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub till the spirit level reviews level.
To install faucets, fit the bottom of the furthest flexible tap adapter to the ideal supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub and additionally check the overflow outlet and also the normal outlet for leakages.
Ultimately, repair the bath paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait until the bathtub has been utilized at least when as this will certainly settle it right into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, after that you will need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Secure the faucet in position with the supplier offered backnut. As soon as the tap is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The former type must be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to break a stiff seal, causing the water to penetrate the wall surface between the bath and the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and also cartridges, and are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the bath tub with water before securing, to permit the activity experienced when the tub remains in usage. The sealer can break rather early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you so much for finding the time to read through our article post. If you enjoyed reading our blog entry please don't forget to share it. I am grateful for your time. Visit us again soon.
Contact for excellence. Report this page